• Die Spacer - 25 ml


    Fast drying die spacers, in a variety of colour shades and thickness gradings. Steam cleaning-resistant with particularly scratch-resistant and smooth surfacing properties. Short curing time; thermal resistant.
    Gold 15 µm , silver 13 µm , red 8 µm , blue 10 µm , clear 5 µm.

      producator S&S Scheftner
      pret : 52,21 lei cu TVA
  • Thinner - 25 ml


    Thinners for Die Spacers. Thickened lacquers and varnishes can be restored to original consistency.

      producator S&S Scheftner
      pret : 48,77 lei cu TVA
  • Hardener - 25 ml


    For hardening, sealing and protecting of dies. The resultant surface is smooth and extremely scratch resistant. Does not build up, is completely absorbed into the plaster.

      producator S&S Scheftner
      pret : 52,21 lei cu TVA








  • Silverspacer - 20 ml

    Creates the desired space for the cement. This die spacer is highly resistant to mechanical attack and immune to all separating agents. This lacquer contains metallic fillers with a precisely standardized particle size which accumulate on line and point angles just the same as on the lower sections of the preparation. This creates a film of uniform thickness of approximately 8 - 10 microns per coating with a finely textured, smooth surface. This lacquer is heat resistant for dipping or thermo-forming techniques and dries quickly.

      producator BENZER-DENTAL AG
      pret /buc : 107,57 lei cu TVA


  • Purargent pure silver - 20 ml

    High class die spacer with smooth surfaces - also for use when fabricating all-ceramic restorations. This lacquer is highly resistant to chemical and mecha­nical attack and creates an absolutely uniform layer of approximately 10 microns, including on line and point angles. Purargent is resistant to all separating agents, dries quickly and is heat resistant. Purargent is also used by Ivoclar AG, Schaan, Liechtenstein, for the IPS Empress System.

      producator BENZER-DENTAL AG
      pret /buc : 183,47 lei cu TVA




  • Margidur by Arnold Wohlwend - 30 ml

    Margidur hardens and seals the die without adding a layer. Critical line angles along the preparation margin are strengthened and their mechanical resistance enhanced. The surfaces become dirt and water repellent. Due to diffusion, no layer is added to the surface. Margidur is also used for the porcelain shoulder technique according to Arnold Wohlwend.

      producator BENZER-DENTAL AG
      pret /buc : 107,57 lei cu TVA


















  • IsoGips - 250 ml

    Insulates plaster impression compounds and plaster models, as well as model stump moulds and model cast bases in saw-cut models. The product is especially designed to treat saw-cut models, for split cast techniques and all model systems.

      producator S&S Scheftner
      pret : 92,37 lei cu TVA

  • IsoGips Classic - 1000 ml

    Conventional separating agent for opposing plaster faces. Also seals porous surfaces. Rapid and secure separations. No film residue.

      producator S&S Scheftner
      pret : 150,60 lei cu TVA

  • IsoSil Silicon Spray - 400 ml

    Silicon spray for treating trimmers, fl asks and vessels, articulators or vibrators. Prevents the adhering of plasters. Protects against aggressive investment compounds.

      producator S&S Scheftner
      pret : 61,39 lei cu TVA


  • BlockStar - 70 g

    A safe special wax for the blocking-out of undercuts and rough surfacings; superb adherring properties to models and not to the instruments. Can be easily scraped; but not suitable as casting wax.

      producator S&S Scheftner
      pret : 71,43 lei cu TVA

  • BlockStar ScanWax - 70 g

    Scanable modelling wax; for all CAD/CAM systemes. For the blocking out of small cavities and for fi lling in saw cuts before scanning. BlockStar Scan Wax ensures density of scan data even when working with thin wax layers ; it guarantees best scan results.

      producator S&S Scheftner
      pret : 103,84 lei cu TVA

  • DoubleStar - Base 1000 ml (1.2 kg) + Catalyst 1000 ml (1.2 kg)

    Duplicating silicone on 'A' silicone basis. Perfect processing due to enormous tear resistance excellent fl ow properties and high dimensional stability. Extraordinary reproduction precision; high degree of elasticity guarantees faultless duplicates.'Shore' hardness: 22. Curing time: 15 mins approx.

      producator S&S Scheftner

  • Debubblizer & Wax Pattern Cleaner - 100 ml

    Surface tension releasing agent. Reduces tension on all wax and silicone surfaces for better fl owing and adhering of investment and plasters. Degreases and cleanses wax objects before investment. Result: smooth and cavity-free castings.

      producator S&S Scheftner
      pret : 43,32 lei cu TVA

  • Debubblizer & Wax Pattern Cleaner - 1000 ml

    Surface tension releasing agent . Reduces tension on all wax and silicone surfaces for better fl owing and adhering of investment and plasters. Degreases and cleanses wax objects before investment. Result: smooth and cavity-free castings.

      producator S&S Scheftner
      pret : 123,06 lei cu TVA

  • GingiStar (Automix) - 2 x 50 ml Cartridges + 12 Cannulas

    Addition curing silicone for the production of gingival maskings; essential for a precise representation of the gingival line, e.g. for implantation work, or for high-class crown and bridge work. Also available in hard version for milling. Good grinding properties combined with superb elasticity and tearing resistance. Ease of handling by means of automatic mixing and direct application from the cartridge.

      producator S&S Scheftner
      pret : 193,63 lei cu TVA


  • GingiStar Hard (Automix) - 2 x 50 ml Cartridges + 12 Cannulas

    Addition curing silicone for the production of gingival maskings; essential for a precise representation of the gingival line, e.g. for implantation work, or for high-class crown and bridge work. Also available in hard version for milling. Good grinding properties combined with superb elasticity and tearing resistance. Ease of handling by means of automatic mixing and direct application from the cartridge.

      producator S&S Scheftner
      pret : 193,63 lei cu TVA

  • Dowel Pins - 1000 buc



    Brass manufacture with and without guide pins in two sizes.

      producator S&S Scheftner

    - # 1: without guide pret/buc: 0,22 lei cu TVA
    - # 1: with guide pret/buc: 0,29 lei cu TVA
    - # 2: without guide pret/buc: 0,22 lei cu TVA
    - # 2: with guide pret/buc: 0,27 lei cu TVA


  • IsoPlast - 100 ml si la 1000 ml


    Formaldehyde-free separating agent (plastics against plasters) for plaster models in acrylic denture works. Excellent insulating eff ect. High degree of fitting precision.

      producator S&S Scheftner
      pret 1000 ml: 85,77 lei cu TVA


Jan Langner JetPin Modellsystem





Modelul este la inceputul tuturor lucrarilor dentare. Inexactitatile unui model gresit duc cu siguranta la o lucrarea gresita. Un model perfect stabileste standardele unui laborator. Modelul si lucrarea reprezinta imaginea laboratorului. Cu sistemele Jan Langner aveti garantata reusita acestui deziderat. Aceste sisteme sunt patentate si functioneaza pe sistemul telescopului conic. NU NECESITA LIPIREA LOR.

Marimi disponibile: 2 mm si 1,5 mm ( ofera posibilitatea de a se arde în cuptorul de calcinare impreuna cu bontul de masa refractara).

  • Jet-Pin 2,0 mm with open Cases + 1 Drill - 1000 buc gri


      producator Jan Langner

      pret = 808.94 lei cu TVA

    Detalii »

  • Jet-Pin 2,0 mm with closed Cases + 1 Drill - 1000 buc rosii


      producator Jan Langner

      pret = 808.94 lei cu TVA

    Detalii »

  • Jet-Block Pin - 1000 buc



      producator Jan Langner

      pret = 447.50 lei cu TVA

    Detalii »



  • Jan Langner JetFix Modellsystem



  • Jet-Fix Pins - 1000 buc

      producator Jan Langner

      pret = 665.51 lei cu TVA

    Detalii »

  • Jet-Fix Bohrer

      producator Jan Langner

      pret = 149.17 lei cu TVA

    Detalii »


  • Jet-Pin 1,5 mm with closed Cases + 1 Drill - 1000 buc alb


      producator Jan Langner

      pret = 889.26 lei cu TVA

    Detalii »


Fix-Pin model system - producator BENZER-DENTAL AG

The Fix-Pin model system is easy to use - no special equipment is required. This high precision technique is based on four different high-grade polycarbonate baseplates which are heat-resistant up to 130° C. The fixed pins have been ground with diamond instruments and their surfaces conditioned to make them corrosion-resistant. The high-grade plastic reduces the coefficient of thermal expansion to a minimum to create a non-distorting, absolutely rigid base. The baseplates include metal plates for magnets and Splitcast components. In daily practice, the Fix-Pin system has proven extremely economical and simple to handle. The K (small) and M (medium) universal baseplates can be used for both upper and lower models. The upper OK and lower UK baseplates are selected specifically for the upper and lower jaws. Small figures and letters have been placed between the pins to facilitate location of the individual dies after sectioning.

  • Fix-Pin model system according to A. Wohlwend (patented system)

      producator BENZER-DENTAL AG

      pret = 790.69 lei cu TVA

    Detalii »


  • The intro set: Fix-Pin by Arnold Wohlwend

    The intro set:
    - 1 x K Base-plate
    - 1 x M Base-plate
    - 1 x UK Base-plate
    - 1 x OK Base-plate
    - 4 x Transfer-plates K/M/OK/UK
    - 1 x 100ml Separating agent
    - 4 x Magnet
    - 1 x Plastic hammer
    - Directions for use

      producator BENZER-DENTAL AG


  • Instructions for Fix-Pin model system

    1. Selecting the optimum base-plate.
    2. Using silicone or plasticine to position the baseplate correctly.
    3. The baseplate should be coated with separating agent and the impression cast and placed on the Fix-Pin base-plate.
    4. The silicone stop enables the impression to be positioned correctly.
    5. After hardening, the arch is released by tapping it lightly.
    6. The arch is easily sectioned with diamond separating discs. No allowance has to be made for the pins because they remain in the baseplate.
    7. Finished Fix-Pin model: Three or four pins per die guarantee the highest possible precision - requires only minimal amounts of material and time.



VERTYSYSTEM a.gree - EQUIPMENTS

  • SPLI CAST & BLACK GUM

    Split-Cast in anodized aluminium for pouring stone models.These new SplitCasts are a great improvement on the old ones. The material used is even more precise and smooth.

      producator VERTYSYSTEM a.gree
      pret/buc = 50 euro cu TVA

  • ARTIC LINK

    Male in techno-polymer and female in alluminium, for creating the model bases which fit to the VERTYSYSTEM® instruments, which can be used with any articulator. These bases have been improved. The techno-polymer used is even more rigid and precise.

      producator VERTYSYSTEM a.gree

  • VERTYS - Verticulator on three axes

    The VERTYS is an instrument that works on three axes.It is made of an anodized aluminum base that sustains three special stainless steel bars. Inside the plexiglass cover can be found three sintered bushes which, combined with the adjustment of the three bars, provide for excellent precision and "controlled" flow. These characteristics are extremely important in the molding of ceramics and paste composites. An indispensable tool for adjusting "wax projects", for checking spaces, for constructing metal girders and for reproducing the occlusal table.

      producator VERTYSYSTEM a.gree
      pret/buc = 583 euro cu TVA

  • ALU BIG

    The ALU BIG is milled from solid using CAD-CAM technology to obtain smooth and precise internal parts, without the slightest undercut. This processing provides for easy and precise silicone reintegration, even after long periods of time. The nuts and spacers are both made from stainless steel. The ALU SMALL has the same characteristics as the ALU BIG, but in a more compact size and is particularly indicated for producing temporary prostheses.

      producator VERTYSYSTEM a.gree
      pret/buc = 447 euro cu TVA
  • ALU SMALL

    The ALU SMALL has the same characteristics as the ALU BIG, but in a more compact size and is particularly indicated for producing temporary prostheses.

      producator VERTYSYSTEM a.gree
      pret/buc = 447 euro cu TVA










  • INCLINED PLANE

    In Toronto Bridge cases where the retention elements in the anterior region do not allow for a straight path of insertion for the acrylic teeth in the mould, these inclined split cast bases bring the path of insertion in line with the insertion plane of the verticulator lid.These inclined bases can also be used in the Vertys Alu Small and Big flasks, giving the same inclination as with the verticulator.

      producator VERTYSYSTEM a.gree
















  • VERTYS FURBO

      producator VERTYSYSTEM a.gree
      pret/buc = 459 euro cu TVA
  • ARTIC PINS

    An impeccable and accurate master model underpins the success of a prosthetic product.

      producator VERTYSYSTEM a.gree
      pret/buc = 347 euro cu TVA

  • VERTYSYSTEM a.gree - VIDEOS










    * Ofertele si preturile sunt valabile in limita stocurilor disponibile. Preturile pot fi modificate fara un anunt prealabil, pot interveni modificari de preturi datorate furnizorilor. Firma AGC New Dent isi rezerva dreptul de a modifica preturile fara notificare prealabila, in conditiile variatiei cursului de schimb valutar peste 1 Euro = 4,5 Lei.